AntMiner S9/S9i/S9j 3.9.0

Release 3.9.0

ATTENTION: The firmware is suitable for all ASICs S9, S9i, S9j.
If, when changing the BITMAIN firmware, you see the message: can not find signature, this means that your equipment has the 2019 BITMAIN firmware installed, in which the overwrite protection is installed, the 2018 firmware does not have this protection.
If you have BITMAIN June 2019 and earlier firmware installed, you can remove the protection using the "signature" file, if you have the firmware on July 31, 2019, you can remove the protection using the "signature_31july" file and then download our firmware or use the SD card (all files are posted on the site and instructions).
You can see the firmware version in the System - file system version section.
If during the flashing process via the SD card you see that 2 lamps (green and red) on the control board are on and do not blink, then most likely your control board is infected with the ANTBUILD virus, you must use a special image ANTBUILD_RECOVERY to block the virus.

INSTALL: Install the firmware from July 31, 2021, from Antminer S9. File: Antminer-S9-xilinx-201907311618-autofreq-user-Update2UBI-NF-sig.tar
1. Run the UNLOCKER file
2. Enter a small Y
3. Enter the ip of the ASIC (or the IP of the first ASIC in the range, if we want to flash several), click ENTER
4. Enter again the ip of the ASIC (or the IP of the last ASIC in the range, if we want to flash several), click ENTER
5. Enter the ASIC password (root by default), click ENTER
6. Check that the unlocker indicated the path to the new firmware and asked if the configuration is ok , click ENTER
7. Wait until the message about the successful completion of the process appears

Energy Consumption Table

Factory firmware от 31.07.2021
Unlocker_vnish
  Update AntMiner S9/S9i/S9j Release 3.9.0   Install SD AntMiner S9/S9i/S9j Release 3.9.0

Popular modes S9,S9i,S9j:

16 TH/s - 1450 watt (90 watt-TH/s)
15 TH/s - 1300 watt (86 watt-TH/s)
13,5 TH/s - 1050 watt (78 watt-TH/s)
10 TH/s - 750 watt (71 watt-TH/s)

FIRMWARE BITMAIN S9,S9i,S9j:
13,5 TH/s - 1300 watt (96 watt -TH/s)

  • Release: 3.9.0

    Downloaded: 2416

    Date: 30.11.2021

    Size of the firmware: 17.8 Mb

    Size of SD image: 51.9 Mb


    Hash Sum of the firmware: 947cd75e9a687a0058095dfdaffbd88a

    Hash Sum of SD image: cd9a4823a6b2594c732bb2c88444bd32


      Update download 3.9.0     Install SD download 3.9.0  

    What's new:

    1) Added unique protection. On the hardware level against Antbuild and all similar viruses forever!!
    2) Added a hotel fii option (where you can redirect part of the capacity to pay for electricity, equipment placement or pay for miners' maintenance).
    3) Added option to enable LPM mode (voltage reduction during mining).
    4) Changed the visual display of hash boards (it is easier to physically find the hash board in the miner).
    5) Added the ability to reduce the voltage on hash boards to 7.9 volts.


  • Release: 3.8.7

    Downloaded: 327

    Date: 08.11.2021

    Size of the firmware: 17.7 Mb


    Hash Sum of the firmware: 33d7e20e1dba948583994f3ed8300d87


      Update download 3.8.7  

    What's new:

    1) Added unique protection. On the hardware level against Antbuild and all similar viruses forever!!
    2) Added a hotel fii option (where you can redirect part of the capacity to pay for electricity, equipment placement or pay for miners' maintenance).
    3) Added option to enable LPM mode (voltage reduction during mining).
    4) Changed the visual display of hash boards (it is easier to physically find the hash board in the miner).
    5) Added the ability to reduce the voltage on hash boards to 7.9 volts.


  • Release: 3.8.6

    Downloaded: 10854

    Date: 17.03.2021

    Size of the firmware: 13.7 Mb


    Hash Sum of the firmware: 85929dd6e7aa98653d9fe39b213bab79


      Update download 3.8.6  

    What's new:

    1) General stability.
    2) Added the ability to choose between a full restart of the ASIC and the restart of only the cgmeiner in tune.
    3) In addition to the automatic virus scanning system, Added manual scanning and disinfection in the Security section, including the new AntBuild virus. 4) Fixed connection to monitoring Anthill.farm
    5) Added the Find Miner function to the multiplier config to search for more miners at once.
    6) Changed the format of downloading the log file in txt.
    7) a new function "sleep mode" when it is turned on, mining stops and the fans go down to minimum speed. The function is available in the config multiplier.
    8) Fixed the problem with DevFee error exit.


Chronology of changes by release.

Gallery

Installation and configuration in pictures.


Video

You can get acquainted with the advantages of the firmware and the main functions by watching the video:


Do you want to cooperate with us?

We offer our partners beneficial cooperation

Vnish offers special partnership terms for owners and administrators of large mining farms. For wholesalers, mining equipment and major repair services!

As a partner you will receive:

  • Personal assembly of the firmware with your logo and your commission
  • 24/7 technical support for integrating and configuring the firmware.
  • Priority of updates - new firmware versions, before official releases